blog

Not All Clear Plastics Are The Same! Know Your Different Types

temp-post-image

Many people assume that plastic is plastic, but saying all plastic is the same is much like saying all wood is the same or that all metal is the same. Replex primarily uses two different types of transparent polymers (clear plastics). Each polymer has different properties, different benefits and drawbacks, and are generally used for different applications. There are several other transparent polymers available in the industry; but they are generally not used in mirrors very often, if at all. We will explain why.

The two polymers primarily used by Replex are represented by complicated chemical names that few can remember or spell, so the result is an alphabet soup of acronyms:

Polymethylmethacrylate acrylic is just called “acrylic” or “PMMA;”

Polycarbonate often becomes “PC;”

Just as balsa wood and mahogany are totally different, these two classes of polymers are radically different from one another. Furthermore, in the case of acrylic these is a big difference between extruded acrylic versus cell cast acrylic. Both are forms of PMMA, but are made by totally different manufacturing processes that result in some important property differences, leading to different end uses.

The following chart offers a glimpse into the differences, uses and applications of these materials.

Extruded Acrylic (PMMA)

Cell Cast Acrylic (PMMA)

Polycarbonate (PC)

Typical End Uses:

Convex mirrors,

dome mirrors &

skylight domes

Camera domes

Playground domes & some skylights

Beneficial Material Features:

Very clear, UV stable, great optics, uniform thickness, scratch resistant versus PC due to hardness. Low cost. Hard and clear

Has unique forming properties suitable for camera domes.

Highest resistance to breakage due to high impact strength. Highest maximum service temperature and best fire rating.

Negative Features or Disadvantages:

Hardness results in brittleness compared to PC.

Poor thickness uniformity & more expensive than extruded acrylic.

Needs protection for UV stability. Softness renders PC very susceptible to scratching unless coated. Highest cost.

Impact Resistance:

Much better than glass, but inferior to PC. Does not stretch much before breakage. Can be improved by adding impact modifier.

Similar to extruded acrylic in this respect, but is not available with impact modifiers.

Highest impact strength, often considered “unbreakable” in most applications.

UV Resistance:

Excellent: typically, durable 10-20 years in outdoor applications under full sun, or longer if given extra UV protection.

Depends highly on the manufacturer, grade, and UV protection. Can be good or bad for outdoor uses.

Not as naturally UV stable as extruded acrylic. Typically lasts 3-5 years outdoor unprotected, 10 years with a UV protection layer.

Fire Performance:

Burns thoroughly and cleanly with minimal smoke. Adds fuel to any fire.

Same as extruded acrylic.

Somewhat fire retardant; more so with special additives. If burned, smoke is very toxic.

Indoor/Outdoor Usages:

Our most commonly used polymer. Its optics, UV stability, scratch resistance make it excellent for use in mirrors, both indoors and outdoors. Very safe compared to glass. Also, very lightweight compared to glass.

Typically limited to camera domes at Replex due to higher cost, and poor thickness uniformity compared to extruded acrylic.

Used anywhere that safety is a prime consideration, such as playgrounds, eyeglasses, safety goggles and hockey visors. High impact strength makes it good for vandalism-prone mirrors, such as those found in prisons. Used for skylights in hurricane prone areas.

Known Brands:

Optix™

Plexiglas™

Acrylite ™

N/A

Lexan™

Cost:

Lowest cost among these three material types, both to purchase and to manufacture into domes.

Manufacturing process makes this more expensive than extruded acrylic.

Most expensive of the three material types, and more expensive to process as well. Must be dried before forming.

Some other polymers that are transparent include PETG (glycol modified polyester), PS (polystyrene), and some grades of PVC (polyvinylchloride).

PETG is sometimes used in mirror with low optical requirements (such as inexpensive toys) but is not UV stable whatsoever, and this greatly reduces the application range for this polymer. Polystyrene (PS) is quite brittle and therefore cracks too easily for most durable goods. PS is more commonly used in disposable applications where long-life is not required. PVC is very tough and durable but is a bit too cloudy to make a high-quality mirror.

Hence the decision generally boils down to finding the best balance of properties between extruded acrylic, cell cast acrylic, or polycarbonate. The requirements of the end use will dictate which polymer is the best choice.

Contact Us

11 Mount Vernon Ave
Mount Vernon, OH 43050
sales@replex.com 
1-800-886-8847 (U.S.A Only)
+1-740-397-5535

                                           

 Want More Information on Replex Products?

Whether it's a transportation mirror safety and security mirror, plastic dome, or other custom products, we're happy to answer all your questions.

Replex Reads

Sign up to receive monthly updates from Replex!